Coleman Tent 2000001588 User Manual

®
ELITE WEATHERMASTER 6 SCREENED TENT  
MODEL 2000001588  
Before you begin  
Fig. 6  
Curved Ridge Poles with Red Markings in center sleeves  
Read all instructions before set up.  
• Select a level site clear of rocks, branches, and other hard or sharp  
objects, to install your tent.  
WARNING: Keep clear of overhead power lines.  
• Do not set up your tent under trees because of potential lightning strikes  
or falling tree limbs in inclement weather.  
• Secure with all stakes and guylines provided to prevent property damage  
or personal injury.  
• For best results in windy conditions, position narrow end of tent into  
the wind.  
• Enlist the help of at least one other person to assist you when it is time  
to assemble the tent.  
6. Rotate all eight Leg Poles upright and insert pin on  
each web loop at the side locations as shown.  
(Fig. 7 & 7A)  
7A  
Pin  
Pole Descriptions  
Pole  
Pole  
Pole  
Description  
Qty. Dia.  
Repair Kit Replacement Kit  
Long Leg Pole, steel  
(w/ red marking)  
4
4
19mm  
19mm  
N/A  
N/A  
5010000608  
5010000610  
Short Leg Pole, steel  
Curved Ridge Pole, steel  
(w/ red marking)  
Curved Ridge Pole, steel  
Awning Pole, black,  
fiberglass, metal tips  
Door Pole, long, thin, black,  
fiberglass, rubber tips  
Vert. Door Pole, short, black,  
fiberglass, rubber tips  
2
2
19mm  
19mm  
N/A  
N/A  
5010000607  
5010000609  
1
1
1
6.3mm 5010000543 5010000545  
6.3mm 5010000543 5010000545  
6.3mm 5010000543 5010000545  
Fig. 7  
7. Locate the plastic hooks at sides and  
corners of tent, then snap onto Leg  
Poles to attach. (Fig. 8)  
Self-Rolling Window Spring Descriptions  
Fig. 8  
Fig. 9  
Color Code Description  
Qty.  
Length Replacement Part No.  
Red  
Green  
Orange  
1
3
2
360mm  
610mm  
670mm  
5010000624  
5010000627  
5010000628  
8. To stretch tent to finished size:  
• Push in button on Leg Pole while  
twisting lower Leg Pole section  
counterclockwise (Fig.9);  
Upper  
CAUTION: “Springs” may have sharp edges. Handle with care to avoid  
injury. Keep out of reach of children.  
Leg Pole  
Section  
• Pull up on top Leg Pole section until  
tent is taut;  
Button  
• Twist the lower Leg Pole clockwise  
until the button locks into the center  
or lowest hole;  
To Set Up Tent  
Center Hole  
Lower Hole  
1. Unfold tent and spread out on a clean, level surface with the door  
facing the desired direction. Unzip doors. (Fig. 1)  
Lower  
• Repeat on remaining Leg Poles.  
Leg Pole  
Section  
Fig. 1  
9. Insert plastic stakes through web straps located  
on both sides of tent, then drive in to secure.  
(Fig. 10)  
Door  
NOTE: It may be necessary to remove metal  
stakes through web straps at side of tent and  
screen room, pull tent taut, and drive in stakes  
to secure.  
2. Pull four corners of tent taut, then secure by  
driving stakes through web loops at an angle for  
better anchoring. (Fig. 2)  
Fig. 10  
Hinged, Rigid Door  
1. Assemble Vertical Door Pole (shorter black pole with plastic tips);  
then insert through zippered vertical pole sleeve on hinged side of  
door. (Fig. 11)  
Fig. 2  
3. Assemble four, steel, shock-corded, curved  
Ridge Poles. Insert Ridge Poles (with red  
marking) into center sleeves on top of tent  
with the red trim (Fig. 3). Insert the remain-  
ing curved Ridge Poles into the other two  
sleeves on top of tent.  
Fig. 3  
2. Insert end of Vertical Door Pole into bottom hinge plate, apply  
pressure to form a slight bow, then insert other tip of pole into top  
hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)  
Ridge Pole  
with Red  
Marking  
3. Assemble Door Pole (longer black pole with plastic cap tips); then  
insert into zippered pole sleeve at top of door. (Fig. 14)  
4. Insert end of Door Pole into top hinge plate, apply pressure to form  
a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)  
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)  
Sleeve  
with Red  
Trim  
4. Assemble eight, steel, shock-corded, Leg  
Poles. Push down on steel button on tapered  
end and insert into end with four holes.  
NOTE: Make sure steel button locks into  
third hole on pole as shown. (Fig.4)  
5. Insert curved end of Leg Poles  
(with red marking) into the  
Fig. 11  
Fig. 12  
Fig. 13  
Vertical Pole  
Sleeve  
Button in third hole  
Fig. 4  
Door Hinge  
ends of the Ridge Pole  
Ridge Pole with  
Red Marking  
(with red marking). Insert  
curved end of remaining  
short Leg Poles into the  
ends of the remaining  
Fig. 15  
Fig. 14  
Top  
Ridge Poles. (Fig. 5 & 6)  
Door  
Hinge  
Sleeve  
with Red  
Trim  
Curved End of  
Long Leg Pole  
Pole  
Sleeve  
Fig. 16  
Fig. 5  
 
(continued on other side)  

Crown Equipment Automobile Series TS User Manual
Danby Range DR2009WGLP User Manual
Directed Audio Automobile Alarm VSS 204TW User Manual
Eclipse Fujitsu Ten Car Stereo System CD4000 User Manual
Electro Voice Speaker System FRI+152 94 User Manual
EverFocus Security Camera EPD200 User Manual
Everpure Water System MRS 100 User Manual
Fundex Games Games Hopscotch User Manual
Fundex Games Games Sea Battle User Manual
GE Trash Compactor ZCG3100 User Manual